Course Contents
-
-
Course Advert
FREE PREVIEW -
Contents of the EOOW Exam
-
Contents of MIN 654
-
How to Prepare for the orals exam
FREE PREVIEW -
What to expect in the oral exam (Face to Face)
-
What to expect in the oral exam (Online)
-
-
-
Self Assessment 1 Questions
-
Self Assessment 1 Questions and Answers
-
Self Assessment 2 Questions
-
Self Assessment 2 Questions and Answers
-
Self Assessment 3 Questions
-
Self Assessment 3 Questions and Answers
-
Self Assessment 4 Questions
-
Self Assessment 4 Questions and Answers
-
-
-
Watchkeeping Introduction
-
Describe the vessel particulars (Power, length, weight, size) of your last vessel.
-
When you join a ship, what would be some of the first things you do as a new 3rd Engineer
-
Watchkeeping Explain How you would take over a watch as 3rd engineer-1
FREE PREVIEW -
How would you hand over the watch to the next watch keeper
-
During UMS you receive an alarm in your cabin from the engine room, describe how you would respond to this
-
During your watch, you discover a fire in the purifier room, what would you do
-
The exhaust temperature on unit 1 (two stroke) is high and rising. Explain your actions
-
What actions would you take in the event of a collision Assume you are on watch
-
While on watch the bridge informs you that black smoke is coming from the funnel. What could cause this
-
What checks would you carry out during your walk round 2 stroke
-
What checks would you carry out on the main engine during your walk-round
-
The boiler water level is low and cannot be seen in the gauge glasses. Explain your actions
-
What checks would you carry out during your walk round 4 stroke
-
After entering the machinery space, you notice one of the bilges is filled with water. What are your actions
-
What is a crank case explosion
FREE PREVIEW -
What is the point of an oil mist detector and how would you respond if it went off during your watch
-
A blackout has occurred, what would your actions be. (What systems need to be reset
-
-
-
Main and Auxiliary Systems Introduction
-
Sketch the timing diagram for a typical four stroke engine
-
Sketch the cross section of a 4-stroke engineii
-
Sketch the timing diagram for a typical two stroke engine.
-
Sketch the cross section of a 2-stroke engine ii
-
What shutdowns are present on your main engine (2 Stroke)
-
What shutdowns are present on your main engine (4 Stroke)
-
What daily, weekly, and monthly checks and maintenance was carried out on the main engines
-
How would you blow down a boiler gauge glass?
-
How to start up a boiler.
-
What mountings did your boiler have?
-
What checks did you carry out on the compressed air system?
-
Sketch and describe the Fuel Oil system on board your last vessel
-
Sketch the LT and HT Cooling water system on your ship
-
Describe the operation of bilge and OWS system on your last ship that had them
-
What is the purpose of the following engine parts piston, Piston Rings, Cylinder Liner, Crankshaft, Cam Shaft Gudgeon Pin and Piston Rod
-
How would you start the main engine from cold (Two Stroke)
-
-
-
Electrical Systems Introduction
FREE PREVIEW -
What would happen if paralleling a gen 10 hz
-
How does the emergency generator start in a blackout
-
How would you go about preparing an electrical motor to work on
-
How does an induction motor work
-
How does the preferential trip system work
-
What are all the readings you would expect to find on the switchboard panel
-
How would you use a multi-meter to prove a motor dead
-
What other equipment can you use to prove the system dead
-
Explain the operation of Air Circuit Breaker
-
What does the synchroscope show you
-
Sketch and describe the following motor starting methods DOL, Star Delta Starter Both Power and Control Circuits
-
What is an earth fault and explain how you would go about locating it
-
-
-
Maintenance Procedures Introduction
FREE PREVIEW -
How would you go about replacing the bearing on a pump
-
How would you ensure that an electrical motor was safe to work on
-
What device would you use to prove a motor dead
-
What kind of planned maintenance system did you have onboard and what information did it hold
-
How would you prepare to make an enclosed space entry
-
What is meant by condition monitoring
-
What is the purpose of a risk assessment
-
Where could you find information on exposure limits for different chemicals
-
How did you record the running hours of equipment
-
Talk me through how you would prepare and clean a plate cooler
-
How would you go about replacing the mechanical seal on the fire pump
-
What equipment would you prepare before making an enclosed space entry
-
What are the dangers of working with chemical cleaning agents
-

What is included
- 314 lessons
- 29.5 hours of video content
- Over 140 Questions and Answers
- Created by UK Maritime and Education specialists
- 26 Past Oral Exams
Give yourself the best chance at passing the EOOW Oral
Here. Now. Today. Buy the best, ditch the rest!